U4743722 HYDRAULIC EXCAVATORS 688C Swing Motor

Cap bolt, SAE grade:8; Max. speed for Taconite seal:440 r/min; P60°:345 kN; PG:1/4 NPT; ba:69.85 mm; R2:33.337 mm; Taconite seal:TER 154; R1:104.775 mm; H1:169.875 mm; da:174.625 mm;

Coefficient of friction µ max.:0.08; Tolerance shaft:h8; Mass bushing:1.25 kg; Effective load carrying cross section A:26700 mm²; Coefficient of friction µ min.:0.03; D:150 mm; Specific static load factor K0:200 N/mm²; d:165 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7;

Basic Static Radial Load Rating Co:11800 N; d:70.000 mm; B:10.00 mm; Accessories:One Shield; Fillet Radius ra:0.60 mm; D:90.0000 mm; Oil Speed Rating Open/Shielded n2:8000 rpm; Sealed Speed Rating n3:4300 rpm; Grease Speed Rating Open/Shielded n1:6700 rpm; Basic Dynamic Radial Load Rating C:12100 N;

Basic Static Radial Load Rating Co:11800 N; d:70.000 mm; B:10.00 mm; Accessories:One Shield; Fillet Radius ra:0.60 mm; D:90.0000 mm; Oil Speed Rating Open/Shielded n2:8000 rpm; Sealed Speed Rating n3:4300 rpm; Grease Speed Rating Open/Shielded n1:6700 rpm; Basic Dynamic Radial Load Rating C:12100 N;

B:25 mm; d:25 mm; Tolerance shaft:h8; Permissible sliding velocity v min.:0.25 m/s; Specific dynamic load factor K:10 N/mm²; Tolerance housing:H7; Permissible sliding velocity v max.:5 m/s; D:30 mm; Mass bushing:0.036 kg; Specific static load factor K0:20 N/mm²;

C:45 mm; r1s (min):2.5 mm; Pu:53.910 kN; T:58 mm; Dynamic (Ca):341 kN; r2s (min):1 mm; d2:75 mm; rs (min):3 mm; D:160 mm; B:55 mm;

B:25 mm; d:25 mm; Tolerance shaft:h8; Permissible sliding velocity v min.:0.25 m/s; Specific dynamic load factor K:10 N/mm²; Tolerance housing:H7; Permissible sliding velocity v max.:5 m/s; D:30 mm; Mass bushing:0.036 kg; Specific static load factor K0:20 N/mm²;

d:220.000 mm; Oil Speed Rating Open/Shielded n2:2200 rpm; B:56.00 mm; D:340.0000 mm; Basic Static Radial Load Rating Co:290000 N; Grease Speed Rating Open/Shielded n1:1800 rpm; Fillet Radius ra:2.50 mm; Sealed Speed Rating n3:1100 rpm; Accessories:Two Seals; Basic Dynamic Radial Load Rating C:247000 N;

r1,2 min.:3.3 mm; Calculation factor Y1:1.7; Fatigue load limit Pu:355 kN; D1 ≈:257 mm; d1 ≈:216 mm; Basic static load rating C0:3750 kN; Calculation factor Y0:1.6; Comparative axial load rating CFa:84.5 kN; D:284.162 mm; Comparative radial load rating CF:430 kN;

B:25 mm; d:25 mm; Tolerance shaft:h8; Permissible sliding velocity v min.:0.25 m/s; Specific dynamic load factor K:10 N/mm²; Tolerance housing:H7; Permissible sliding velocity v max.:5 m/s; D:30 mm; Mass bushing:0.036 kg; Specific static load factor K0:20 N/mm²;

Oil Speed Rating Open/Shielded n2:11000 rpm; Fillet Radius ra:0.79 mm; Shielded or Sealed B1:14.3 mm; Width Plain B:11.1 mm; d:38.100 mm; Accessories:One Seal; Basic Dynamic Radial Load Rating C:16800 N; D:66.7000 mm; Basic Static Radial Load Rating Co:11800 N; Grease Speed Rating Open/Shielded n1:9000 rpm;

B:25 mm; d:25 mm; Tolerance shaft:h8; Permissible sliding velocity v min.:0.25 m/s; Specific dynamic load factor K:10 N/mm²; Tolerance housing:H7; Permissible sliding velocity v max.:5 m/s; D:30 mm; Mass bushing:0.036 kg; Specific static load factor K0:20 N/mm²;

Fillet Radius ra:3.00 mm; Oil Speed Rating Open/Shielded n2:1700 rpm; d:280.000 mm; D:420.0000 mm; Sealed Speed Rating n3:890 rpm; Basic Static Radial Load Rating Co:405000 N; Grease Speed Rating Open/Shielded n1:1400 rpm; B:65.00 mm; Accessories:One Shield; Basic Dynamic Radial Load Rating C:302000 N;

Mass bearing:210 kg; d:360 mm; s1 max.:27.9 mm; Misalignment factor k1:0.117; Fatigue load limit Pu:585 kN; r1,2 min.:5 mm; Basic dynamic load rating C:5000 kN; B:192 mm; d2 ≈:423 mm; Operating clearance factor k2:0.094;

Oil Speed Rating Open/Shielded n2:11000 rpm; Fillet Radius ra:0.79 mm; Shielded or Sealed B1:14.3 mm; Width Plain B:11.1 mm; d:38.100 mm; Accessories:One Seal; Basic Dynamic Radial Load Rating C:16800 N; D:66.7000 mm; Basic Static Radial Load Rating Co:11800 N; Grease Speed Rating Open/Shielded n1:9000 rpm;